The cyanoacrylate super glue formula used in this glue makes all these possible. Along with these, the glue resists water and vibration. It makes the glue highly suitable for repairing car tires. The glue can tolerate extreme pressure, force, harsh bumps, and other conditions. It is reliable, super strong, and perfectly capable of fixing more than just car tires. When you no longer hear the hiss of air, then put one of the rubber inner tube repair patches over area using the repair glue using the repair kit instructions.If you are familiar with car repair kits, you must know the Loctite Ultra Gel Control Super Glue for car tires. Repeat the inflation of the mattress and the air test. If you hear air hissing, then deflate the mattress again, put a small amount of shoo goo along the length of the tear area, and around the exposed foil, use the hair dryer. You may still hear a small hiss of air escaping from the area. Use your hands to apply pressure around the repaired area. Once the Shoo Goo is dry, inflate the mattress half way. Use the hair dryer again gently warm the area until the Shoo Goo is dry. Then use the tongue depressor again to press and hold down this piece of the foil flat to the mattress surface until the Shoo Goo begins to dry. Use the hair dryer to warm the area again, and then use a pair of tweezers to pull the other side of the tear as close to the exposed foil while pressing the foil down over the other side of the tear. Now, apply a small amount of the Shoo Goo to the bottom of other half of the aluminum foil sticking out of the tear. This will make a pliable,flexible seal of one side of the tear. Then using the hair dryer (lowest heat setting) warm the area, moving the hair dryer back and forth over the inserted foil lip until the Shoo Goo sets. Use a tongue depressor, or the flat end of a butter knife to press down on the top of the tear with the foil underneath. If the puncture or tear is wide or large compared to the patch, use a electric hair blower to apply heat to the area around the puncture so it softens and can stretch easily.Ĭut out a small thin piece of heavy aluminum foil that is a about 1/2" in length and approx twice as wide as the tear, apply a small dab of Shoo Goo to one side of the foil, gently lift one lip of the tear and insert the foil half way into the hole leaving the other half sticking outside the tear. Allow the area to dry completely before proceeding to the next step. Use a cotton swab dipped into a small amount of nail polish remover to clean the area around the puncture hole. Use this solution if the tear is larger compared to the repair kit patches.īe very careful when sanding the tact felt around the puncture point not to 'thin' the material to the point where you weaken the area creating a possible weak point for another leak. Here are several suggested changes to the instructions to use the inner tube patch solution described here. It's held for several inflation's now! Anyone have any easier ways to get the same results? Thanks, Tab. So I put a big blob of the E6000 adhesive on a plastic bowl and waited for it to set up a bit but still be pliable and placed it into and over the large year and allowed it to dry completely. I purchased a Intex Dura-Beam Plus Queen size and I began getting small holes after a few uses then during an extended period of use 2 of the seems popped (but didn't mess up the mattress at all other than it looked 9 months pregnant in that area but the popped seems put pressure on other areas and it started getting LARGE TEARS along those seems that are extremely difficult to repair with a patch. 2) E6000 is a really good long lasting adhesive for multiple surfaces and can be found even at your local Dollar store. Also, if u look at the mattress the side that looks more deflated is usually a good starting point to check for a hole. 1) A spray bottle with soapy water in it is an easy way to find a hole.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |